Roof pitch describes how steep a roof is. It is commonly written as a ratio such as 6/12, meaning the roof rises 6 inches for every 12 inches of horizontal run. Knowing the pitch helps with preliminary roof-area estimates, material planning, and communicating roof geometry. It is only one measurement, however; it does not replace a complete roof survey or structural assessment.
What rise and run mean
Rise is the vertical distance a roof climbs. Run is the horizontal distance over which that rise occurs. For a conventional symmetrical gable roof, the common-rafter run is usually measured from the outside bearing line of one exterior wall toward the ridge, not across the entire building width. Keep rise and run in the same unit before dividing them.
For example, a rise of 6 inches over a 12-inch run gives a pitch of 6/12. A rise of 8 inches over a 12-inch run gives 8/12. A larger first number means a steeper roof.
How to calculate roof pitch
Use this relationship: pitch ratio = rise ÷ run. To express the result in the familiar inches-per-12 format, multiply the ratio by 12. If rise and run are 6 and 12, the ratio is 0.5 and the pitch is 6/12.
Use the same unit for rise and run. Mixing inches with feet without converting first produces an incorrect pitch.
The roof angle can also be calculated from the ratio: angle = arctangent(rise ÷ run). A 6/12 pitch is approximately 26.57 degrees. The angle is a different way to describe the same slope; it is not the pitch ratio itself.
Pitch, percentage, and angle are not interchangeable
A 6/12 pitch is a 50% slope because the rise is half the run. Its angle is approximately 26.57 degrees. These three descriptions refer to the same geometry but use different scales. When reading plans or product instructions, check which format is being used rather than assuming a percentage is a pitch ratio.
What is a slope multiplier?
A slope multiplier converts a horizontal plan measurement into the length measured along the roof surface. It is calculated as the square root of 1 plus the pitch ratio squared. For a 6/12 pitch, the multiplier is about 1.118. A 1,000-square-foot horizontal footprint therefore corresponds to about 1,118 square feet of sloped surface when the roof planes share that pitch and the footprint is measured consistently.
Use the RafterNest Roof Pitch Calculator to calculate the pitch ratio, angle, percentage slope, and multiplier from rise and run. The Roof Area Calculator uses the multiplier for a preliminary surface-area estimate.
How to get a reliable measurement
- Start with a trustworthy source such as construction drawings, a roof report, or measurements supplied by a qualified roofing professional.
- If measuring an accessible structure, identify a clear horizontal run and its corresponding vertical rise; do not estimate the ratio from a photograph.
- Record the units beside every measurement and keep the same units throughout the calculation.
- For roofs with multiple pitches, calculate each distinct roof plane separately rather than applying one pitch to the entire building.
Common roof-pitch mistakes
- Using the full building width as the run when the calculation requires half the span for a common rafter.
- Dividing a rise in inches by a run in feet without converting units.
- Treating 6/12 as 6 degrees or as a 6 percent slope.
- Assuming every roof plane has the same pitch, especially on additions, dormers, and complex roofs.
Frequently asked questions
Is a 6/12 roof pitch steep?
A 6/12 pitch is a moderate slope in common residential roof descriptions. Whether it is suitable for a specific covering depends on the product instructions, local requirements, climate, and roof design.
Can I calculate pitch from the roof angle?
Yes. The pitch ratio is the tangent of the angle. To express it as inches of rise per 12 inches of run, multiply that ratio by 12.
Does roof pitch tell me the roof area?
No. Pitch describes steepness. To estimate roof area, you also need the horizontal dimensions of the roof footprint, overhangs where relevant, and the geometry of each roof plane.
Next step
Calculate your own measurements with the free Roof Pitch Calculator. For project planning, continue with our guide to estimating roof area and common rafter length calculator.